ASTM D7091 PDF

This standard is issued under the fixed designation D ; the number 1 This practice is under the jurisdiction of ASTM Committee D01 on Paint and. Related. In nearly the same timeframe, the version of ASTM D, “Standard Practice for Nondestructive Measurement of Dry Film Thickness of. ASTM D describes three operational steps that must be performed prior to coating thickness measurement to help assure the reliability of.

Author: Tojara Duramar
Country: Chile
Language: English (Spanish)
Genre: Science
Published (Last): 4 April 2017
Pages: 87
PDF File Size: 19.32 Mb
ePub File Size: 16.97 Mb
ISBN: 945-3-71966-786-8
Downloads: 95730
Price: Free* [*Free Regsitration Required]
Uploader: Samukazahn

Equipment manufacturers produce non-destructive coating thickness testing gages that are used to measure the cumulative thickness of the coating layers, after they are dry. It is recommended that the gage be veri?

You do not need asym zero the gage. Even if a project speci? August 31, at 6: Non-compliant areas are demarcated using removable chalk or another specified marking material and documented. In general, asym user should remain a minimum of 25 mm 1 in. It is recommended that the gage 5 be veri? In this case, the user will need to obtain base metal readings BMR from the prepared, uncoated substrate described earlier for Type 1 gages.

The steps are incorporated by reference in SSPCPA 2 and are completed before obtaining coating thickness measurements to determine conformance to a specified coating thickness range. Magnetic pull-off gages are categorized as Type 1 Fig.

Some carts may have several small pipe sections, and the total coated surface may exceed square feet. Using the same example, if a two-point verification procedure is adopted, then a two-mil and an eight-mil set of coated standards slightly below and above the intended range of use is appropriate.

The thickness of each layer must be measured after it is applied. Verification of gage accuracy is typically performed using certified coated thickness standards for Type 1 or Type 7d091 gages or certified shims Type 2 gages. One axtm is through training and education.

Measuring Dry Film Coating Thickness According to SSPC-PA 2

Per Specification Conformance to Specified Thickness: Obtaining coating thickness measurements according to the frequency described in SSPC-PA 2 across the entire structure may be of little value during a coating failure investigation and can be cost prohibitive.

  ANTONI RAFALSKI SKRZYPCOWE ABC PDF

Spot measurements are obtained on repeating structural units or elements of structural units until two consecutive units in each direction are conforming or until there are no more units ast, test. Keane Award of Merit.

It, too, was published in The manufacturers provide information for the adjustment and use of these gages, normally in the form of operating instructions. Acquisition of more than three gage readings within a spot is permitted. The two documents are designed to be used together.

You can produce one without the other. Type 1 and Type 2 gages can be veri? Appendix 9 was added as a cautionary statement, as coating thickness data collected during a coating failure investigation are not typically acquired in spots or areas, but rather in failing and non-failing areas, based on observed patterns of failure, etc.

Measuring Coating Thickness According To SSPC-PA2 – Update KTA University

Determining the Magnitude of Non-conforming Thickness. A one-year calibration interval is a typical starting point suggested by gage manufacturers. The minimum value of ? It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. ashm

For areas of coating exceeding 1, square feet, three random areas are x7091 from the first 1, square feet, plus one additional area for each additional 1, square feet. For example, the thickness may need to be measured in each 9 m2 ft2 area in accordance with 8. Even then, the thickness of the measured layer is the cumulative thickness of that layer and all layers beneath it, down to the base metal. That is, no allowance is made for variant spot measurements e.

To guard against measuring with an inaccurate gage, SSPC-PA 2 requires that gage accuracy be verified adtm a minimum at the beginning and end of each work shift according to the procedures described in ASTM D The revisions took five years to complete. The magnetic force of attraction to the steel substrate beneath the coating is opposed by 7d091 spring or coil. NOTE 1—This practice addresses only metal substrates. These readings represent themeasurement device. If a large number of measurements is being obtained, the user may opt to verify gage accuracy during measurement acquisition e.

  KHALED ANATOLIOS PDF

Satm practice does not address the use of ultrasonic coating thickness gages. The governing specification is responsible for providing the user with the minimum and the maximum coating thickness for each layer, and for the total coating system.

Measured shims individually labeled with a stated thickness value commonly supplied with Type 2 gages can also be used for gage adjustment. Therefore, it is important for the specifier to indicate an acceptable range for each coating layer, as the coating may not perform at the lower thickness.

This section lists the items to report when documenting dry film thickness data, including: Level 1 is the most restrictive and does not allow for any deviation of spot or area measurements from the specified minimum and maximum thickness, while Level 5 is the least restrictive.

Acceptable spot measurements are defined by the minimum and maximum values in the contract documents. He holds an A.

Measuring Dry Film Coating Thickness According to SSPC-PA 2KTA University

Click Here to Read the Updated Article. January 29, at Secondly, some Type 2 gages cannot be adjusted. Place the gage probe on a certified coated standard and adjust the gage as necessary. Measurement of Coating Thickness Step 5: April 6, at The number of areas that must be measured for coating thickness varies, depending on the size of the coated area.