HYPERTHERM HPR260XD MANUAL PDF

Hypertherm, HyPerformance, HyDefinition, LongLife and CommandTHC are trademarks of .. HPRXD Manual Gas – Revision 2. guarantees the Hypertherm quality you can count on. The HPRXD delivers superior bar ( psi) Manual gas console. 8 bar ( psi). ArcGlide, EDGE Pro, Hypertherm, HPR and Sensor THC are trademarks of Hypertherm, Inc. and may be When you see a safety symbol in this manual or on your machine HPRXD, HPRXD with a built-in.

Author: Jugal Gardajinn
Country: Mayotte
Language: English (Spanish)
Genre: Spiritual
Published (Last): 25 November 2010
Pages: 37
PDF File Size: 11.7 Mb
ePub File Size: 9.53 Mb
ISBN: 380-8-16907-814-5
Downloads: 26356
Price: Free* [*Free Regsitration Required]
Uploader: Kesar

If the gantry runs manusl rails that are not welded to the table, then the rails need to be connected with a ground cable from each end of both rails to the table.

Safety Instruction for Wireless Products If your computer has wireless function, all safety instructions must be read carefully and must be fully understood, before attempting to use our Wireless Products.

The display will show the current again. Consult with a local expert to implement a site plan to ensure safe air quality. True Comfort offers two types of hyperrherm.

Equipment used for calibration or measurement. Fumes produced vary depending on the metal that is cut.

Connect the power leads to the terminals hr260xd TB as shown below. In some cases, the metal may be coated with a substance that could release toxic fumes. Tome las siguientes precauciones al operar el sistema: Keep the safety labels on your machine in good condition.

If possible, run power and signal cables in separate cable tracks.

HyPerformance Plasma. HPRXD Manual gas. Instruction manual Revision 2 – PDF

Push back the braided cover and slide the sleeve over the leads. Provide a disconnect switch close to the power supply with properly sized fuses. See Installation section for details. The pump will run continuously while 8 is pressed. Electric shock prevention All Hypertherm plasma systems use high voltage in the cutting process to VDC are common.

  JAKE KOSEK UNDERSTORIES PDF

Please find attached a revised amendment letter, extending the contract until 31 st December Use water purifi ed by any method deionization, reverse osmosis, sand fi lters, water softeners, etc. Avant le coupage, retirer de ses poches tout objet combustible comme les briquets au butane ou les allumettes. The power supply has a serial interface hpr260cd provide communication with a CNC controller.

A separate cable must run from the lifter to the bus bar on the gantry. To reduce magnetic field hazards: Water that does not meet the maximum purity specifi cations below can also cause problems.

In no event shall Hypertherm be liable for injury to persons or property damage manula reason of any code violation or poor work practices.

Hold the torch assembly in place with the spanner wrench and remove the mounting sleeve from the torch assembly. I hyperthern an earth ground Protect ears from noise. Use placards or signs.

The external relay s life may be improved by adding a metallized-polyester capacitor 0. Should you fail timely to notify Hypertherm and seek hyperther, approval as set forth herein, the Warranty set forth herein shall be null and void and you will have no further recourse against Hypertherm under the Warranty or otherwise.

Hypertherm HPRXD

Store PC boards in anti-static containers. The shielding should be connected to the cutting mains supply mnual that good electrical contact is maintained between the conduit and the cutting power source enclosure. The CNC cable must be constructed using cable with degree shielding and metal housing connectors at each end. I’ll be happy to get you running!

  HI 99163 PDF

HyPerformance Plasma. HPR260XD Manual gas. Instruction manual Revision 2

Mount the console on top of the power supply or near the CNC on the cutting table. Maximum cable length from the console to the off-valve assembly is 20 m 65 ft.

Hyperthemr length of the hoses from the torch to the metering console are critical to cut quality and consumable life. The ignition console converts 20 VAC control voltage from the power supply into high-frequency and high-voltage pulses kv to break over the torch electrode-nozzle gap.

Use local exhaust ventilation to remove fumes from the air. BZT acts as a corrosion inhibitor for the copper based coolant system contained in the plasma system.

Document Outline

Do not cut pressurized cylinders, pipes, or any mahual container. To prevent leaks in the system, tighten all and water connections as shown below: Arun, Hypertherm have a PDF download on improving hole cut quality. Originally Posted by pontiacg5.

NEVER permit children to operate or play with door control push buttons or remote control transmitters.